Evidence-led vulnerability intelligence · 2026-10-26 22:47 IST

CVE-2026-82390

The Espressif AES driver drivers/crypto/crypto_esp32_aes.c advertises a multi-session cipher API — it hands out up to CONFIG_ESP32_CRYPTO_AES_SESSIONS_MAX (default 4) independent sessions, each carrying its own key and direction. The AES peripheral, however, has a single chip-global set of key and mode registers, and aes_begin_session() programmed them exactly once, at session start, outside the aes_lock mutex that serialises the transforms. The per-operation handlers aes_ecb_op(), aes_cbc_op() and aes_ctr_op() then ran aes_hal_transform_block() against whatever key and direction the registers happened to hold. As a result, once a second session is opened with a different key, every subsequent operation on the first session silently uses the second session's key and direction, and no error is reported. Because the key programming happened outside the lock, the correct usage pattern of "each thread does begin, then op, then free on its own session" also races: a second thread's cipher_begin_session() landing between the first thread's begin and its operation makes that operation run under the second thread's key. An attacker who can induce session creation on the device — for example a protocol peer whose connection causes a session key to be installed — can influence which key is resident when a victim operation runs. The impact is a cryptographic failure rather than memory corruption: data the application believed it was protecting under one key is encrypted or decrypted under another. Where the resident key is one the attacker knows or supplied, the affected plaintext becomes recoverable by that attacker, and the operation's direction (encrypt versus decrypt) can likewise be inverted. Exposure requires an application that holds two or more concurrent sessions with different keys against this driver; no in-tree Zephyr subsystem does so today (the 802.15.4 security layer, which does open two sessions, uses CCM mode, which this driver rejects), so the risk falls on application code that uses the documented multi-session API. The fix removes all hardware access from aes_begin_session() and reprograms the key and direction at the top of every operation, inside aes_lock, so the chip-global registers can no longer be observed stale by another session.

LOW · 3.7

Executive briefing

The source record describes: The Espressif AES driver drivers/crypto/crypto_esp32_aes.c advertises a multi-session cipher API — it hands out up to CONFIG_ESP32_CRYPTO_AES_SESSIONS_MAX (default 4) independent sessions, each carrying its own key and direction. The AES peripheral, however, has a single chip-global set of key and mode registers, and aes_begin_session() programmed them exactly once, at session start, outside the aes_lock mutex that serialises the transforms. The per-operation handlers aes_ecb_op(), aes_cbc_op() and aes_ctr_op() then ran aes_hal_transform_block() against whatever key and direction the registers happened to hold. As a result, once a second session is opened with a different key, every subsequent operation on the first session silently uses the second session's key and direction, and no error is reported. Because the key programming happened outside the lock, the correct usage pattern of "each thread does begin, then op, then free on its own session" also races: a second thread's cipher_begin_session() landing between the first thread's begin and its operation makes that operation run under the second thread's key. An attacker who can induce session creation on the device — for example a protocol peer whose connection causes a session key to be installed — can influence which key is resident when a victim operation runs. The impact is a cryptographic failure rather than memory corruption: data the application believed it was protecting under one key is encrypted or decrypted under another. Where the resident key is one the attacker knows or supplied, the affected plaintext becomes recoverable by that attacker, and the operation's direction (encrypt versus decrypt) can likewise be inverted. Exposure requires an application that holds two or more concurrent sessions with different keys against this driver; no in-tree Zephyr subsystem does so today (the 802.15.4 security layer, which does open two sessions, uses CCM mode, which this driver rejects), so the risk falls on application code that uses the documented multi-session API. The fix removes all hardware access from aes_begin_session() and reprograms the key and direction at the top of every operation, inside aes_lock, so the chip-global registers can no longer be observed stale by another session. The practical risk depends on whether an affected product/version is present, reachable and configured in an exploitable way. Review the affected-product evidence and linked vendor advisories before assigning exposure status.

Assessment: Potential exposure only — validate the installed product, exact version, configuration and vendor applicability before treating an asset as confirmed vulnerable.

Evidence confidence: Limited Evidence-derived, not an exploitability verdict

Severity & attack characteristics

3.7 / 10 · 3.1

CVSS vector:
CVSS:3.1/AV:N/AC:H/PR:N/UI:N/S:U/C:L/I:N/A:N

Attack vectorN
Attack complexityH
Privileges requiredN
User interactionN
ScopeU
Confidentiality impactL
Integrity impactN
Availability impactN

Technical explanation & impact

The technical mechanism is not expanded beyond the source description unless a referenced advisory supplies additional evidence. Read the linked vendor/CERT advisories for root-cause detail.

Potential impact must be interpreted from the published CVSS impact metrics and the affected component. A CVSS impact score is not proof that a particular asset is exploitable.

Weakness classification

CWE-362

Affected products and versions

NVD has not supplied machine-readable vulnerable CPE product/version entries for this CVE. This is an information gap, not proof that no products are affected. Check the vendor advisory references below.

Remediation & validation

  1. Identify exposure by comparing the affected product and version ranges with your asset inventory, SBOM and externally exposed services.
  2. Review the linked vendor security advisory or patch notes. Upgrade to a vendor-confirmed fixed release; do not infer a fixed version from the CVE description.
  3. Until patched, consider restricting network access or disabling the affected feature where operationally safe. These are temporary controls, not a substitute for a vendor fix.
  4. Validate the remediation with a version check and vulnerability rescan, then retain change evidence.

No fixed version is displayed unless it is explicitly established by a vendor advisory. Follow the vendor's release notes for exact product and branch applicability.

Vendor advisories, patches & exploit references

Information gaps & confidence notes

These gaps indicate missing source data. CVE Watch does not fill them with guessed product, exploit or patch details.

Last enrichment: 2026-11-05T06:02:26+00:00 · Source last modified: 2026-11-04T05:19:03.943

Open NVD record ← Back to CVE Watch