Evidence-led vulnerability intelligence · 2026-10-24 01:47 IST

CVE-2026-79982

The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool. The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization. Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly.

HIGH · 8.8

Executive briefing

The source record describes: The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool. The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization. Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly. The practical risk depends on whether an affected product/version is present, reachable and configured in an exploitable way. Review the affected-product evidence and linked vendor advisories before assigning exposure status.

Assessment: Potential exposure only — validate the installed product, exact version, configuration and vendor applicability before treating an asset as confirmed vulnerable.

Evidence confidence: Limited Evidence-derived, not an exploitability verdict

Severity & attack characteristics

8.8 / 10 · 3.1

CVSS vector:
CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H

Attack vectorA
Attack complexityL
Privileges requiredN
User interactionN
ScopeU
Confidentiality impactH
Integrity impactH
Availability impactH

Technical explanation & impact

The technical mechanism is not expanded beyond the source description unless a referenced advisory supplies additional evidence. Read the linked vendor/CERT advisories for root-cause detail.

Potential impact must be interpreted from the published CVSS impact metrics and the affected component. A CVSS impact score is not proof that a particular asset is exploitable.

Weakness classification

CWE-787

Affected products and versions

NVD has not supplied machine-readable vulnerable CPE product/version entries for this CVE. This is an information gap, not proof that no products are affected. Check the vendor advisory references below.

Remediation & validation

  1. Identify exposure by comparing the affected product and version ranges with your asset inventory, SBOM and externally exposed services.
  2. Review the linked vendor security advisory or patch notes. Upgrade to a vendor-confirmed fixed release; do not infer a fixed version from the CVE description.
  3. Until patched, consider restricting network access or disabling the affected feature where operationally safe. These are temporary controls, not a substitute for a vendor fix.
  4. Validate the remediation with a version check and vulnerability rescan, then retain change evidence.

No fixed version is displayed unless it is explicitly established by a vendor advisory. Follow the vendor's release notes for exact product and branch applicability.

Vendor advisories, patches & exploit references

Information gaps & confidence notes

These gaps indicate missing source data. CVE Watch does not fill them with guessed product, exploit or patch details.

Last enrichment: 2026-11-04T06:02:44+00:00 · Source last modified: 2026-11-04T05:19:03.027

Open NVD record ← Back to CVE Watch