Evidence-led vulnerability intelligence · 2026-08-22 21:46 IST

CVE-2026-74682

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: fix OOB write on Type II inbound URBs data_ep_set_params() sizes each URB transfer buffer before it adds the Format Type II transfer delimiter: u->packets = urb_packs; u->buffer_size = maxsize * u->packets; if (fmt->fmt_type == UAC_FORMAT_TYPE_II) u->packets++; /* for transfer delimiter */ u->urb = usb_alloc_urb(u->packets, GFP_KERNEL); buffer_size is computed from the pre-increment packet count and never recomputed, so for a Type II endpoint the buffer is one packet short of the packet count the URB is built with. prepare_inbound_urb() then lays out one iso frame per packet and never consults buffer_size: offs = 0; for (i = 0; i < urb_ctx->packets; i++) { urb->iso_frame_desc[i].offset = offs; urb->iso_frame_desc[i].length = ep->curpacksize; offs += ep->curpacksize; } urb->transfer_buffer_length = offs; urb->number_of_packets = urb_ctx->packets; The last descriptor therefore points one packet past the end of the transfer buffer, where the host controller writes device data on every inbound transfer. prepare_silent_urb() and prepare_playback_urb() bound their fill loops by ctx->buffer_size, so only capture is affected. fmt_type comes from the device's audio streaming descriptors, so any device advertising a Type II capture format hits this once userspace sets hw_params on the stream. KASAN on 7.2.0-rc5 (arm64) with a dummy_hcd/raw-gadget device, one report per inbound transfer: BUG: KASAN: slab-out-of-bounds in dummy_timer Write of size 64 at addr ffff0000186171c0 by task cons02/166 __asan_memcpy dummy_timer hrtimer_run_softirq Allocated by task 166: usb_alloc_coherent snd_usb_endpoint_set_params The buggy address is located 0 bytes to the right of allocated 64-byte region [ffff000018617180, ffff0000186171c0) Compute buffer_size after the delimiter packet has been accounted for, and bound the fill loop by buffer_size, as prepare_silent_urb() already does on the outbound side. This grows every Type II URB allocation by one maxsize packet. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>

UNRATED · N/ALinux

Executive briefing

The source record describes: In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: fix OOB write on Type II inbound URBs data_ep_set_params() sizes each URB transfer buffer before it adds the Format Type II transfer delimiter: u->packets = urb_packs; u->buffer_size = maxsize * u->packets; if (fmt->fmt_type == UAC_FORMAT_TYPE_II) u->packets++; /* for transfer delimiter */ u->urb = usb_alloc_urb(u->packets, GFP_KERNEL); buffer_size is computed from the pre-increment packet count and never recomputed, so for a Type II endpoint the buffer is one packet short of the packet count the URB is built with. prepare_inbound_urb() then lays out one iso frame per packet and never consults buffer_size: offs = 0; for (i = 0; i < urb_ctx->packets; i++) { urb->iso_frame_desc[i].offset = offs; urb->iso_frame_desc[i].length = ep->curpacksize; offs += ep->curpacksize; } urb->transfer_buffer_length = offs; urb->number_of_packets = urb_ctx->packets; The last descriptor therefore points one packet past the end of the transfer buffer, where the host controller writes device data on every inbound transfer. prepare_silent_urb() and prepare_playback_urb() bound their fill loops by ctx->buffer_size, so only capture is affected. fmt_type comes from the device's audio streaming descriptors, so any device advertising a Type II capture format hits this once userspace sets hw_params on the stream. KASAN on 7.2.0-rc5 (arm64) with a dummy_hcd/raw-gadget device, one report per inbound transfer: BUG: KASAN: slab-out-of-bounds in dummy_timer Write of size 64 at addr ffff0000186171c0 by task cons02/166 __asan_memcpy dummy_timer hrtimer_run_softirq Allocated by task 166: usb_alloc_coherent snd_usb_endpoint_set_params The buggy address is located 0 bytes to the right of allocated 64-byte region [ffff000018617180, ffff0000186171c0) Compute buffer_size after the delimiter packet has been accounted for, and bound the fill loop by buffer_size, as prepare_silent_urb() already does on the outbound side. This grows every Type II URB allocation by one maxsize packet. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> The practical risk depends on whether an affected product/version is present, reachable and configured in an exploitable way. Review the affected-product evidence and linked vendor advisories before assigning exposure status.

Assessment: Potential exposure only — validate the installed product, exact version, configuration and vendor applicability before treating an asset as confirmed vulnerable.

Evidence confidence: Limited Evidence-derived, not an exploitability verdict

Severity & attack characteristics

N/A / 10 ·

CVSS vector:

No CVSS vector is currently available in the source record.

Technical explanation & impact

The technical mechanism is not expanded beyond the source description unless a referenced advisory supplies additional evidence. Read the linked vendor/CERT advisories for root-cause detail.

Potential impact must be interpreted from the published CVSS impact metrics and the affected component. A CVSS impact score is not proof that a particular asset is exploitable.

Affected products and versions

NVD has not supplied machine-readable vulnerable CPE product/version entries for this CVE. This is an information gap, not proof that no products are affected. Check the vendor advisory references below.

Remediation & validation

  1. Identify exposure by comparing the affected product and version ranges with your asset inventory, SBOM and externally exposed services.
  2. Review the linked vendor security advisory or patch notes. Upgrade to a vendor-confirmed fixed release; do not infer a fixed version from the CVE description.
  3. Until patched, consider restricting network access or disabling the affected feature where operationally safe. These are temporary controls, not a substitute for a vendor fix.
  4. Validate the remediation with a version check and vulnerability rescan, then retain change evidence.

No fixed version is displayed unless it is explicitly established by a vendor advisory. Follow the vendor's release notes for exact product and branch applicability.

Vendor advisories, patches & exploit references

Information gaps & confidence notes

These gaps indicate missing source data. CVE Watch does not fill them with guessed product, exploit or patch details.

Last enrichment: 2026-11-07T16:58:29+00:00 · Source last modified: 2026-11-06T17:19:54.510

Open NVD record ← Back to CVE Watch

Threat intelligence, made actionable · CVE data sourced from the NVD