Evidence-led vulnerability intelligence · 2026-07-26 12:46 IST

CVE-2024-14040

In the Linux kernel, the following vulnerability has been resolved: net: nexthop: Increase weight to u16 In CLOS networks, as link failures occur at various points in the network, ECMP weights of the involved nodes are adjusted to compensate. With high fan-out of the involved nodes, and overall high number of nodes, a (non-)ECMP weight ratio that we would like to configure does not fit into 8 bits. Instead of, say, 255:254, we might like to configure something like 1000:999. For these deployments, the 8-bit weight may not be enough. To that end, in this patch increase the next hop weight from u8 to u16. Increasing the width of an integral type can be tricky, because while the code still compiles, the types may not check out anymore, and numerical errors come up. To prevent this, the conversion was done in two steps. First the type was changed from u8 to a single-member structure, which invalidated all uses of the field. This allowed going through them one by one and audit for type correctness. Then the structure was replaced with a vanilla u16 again. This should ensure that no place was missed. The UAPI for configuring nexthop group members is that an attribute NHA_GROUP carries an array of struct nexthop_grp entries: struct nexthop_grp { __u32 id; /* nexthop id - must exist */ __u8 weight; /* weight of this nexthop */ __u8 resvd1; __u16 resvd2; }; The field resvd1 is currently validated and required to be zero. We can lift this requirement and carry high-order bits of the weight in the reserved field: struct nexthop_grp { __u32 id; /* nexthop id - must exist */ __u8 weight; /* weight of this nexthop */ __u8 weight_high; __u16 resvd2; }; Keeping the fields split this way was chosen in case an existing userspace makes assumptions about the width of the weight field, and to sidestep any endianness issues. The weight field is currently encoded as the weight value minus one, because weight of 0 is invalid. This same trick is impossible for the new weight_high field, because zero must mean actual zero. With this in place: - Old userspace is guaranteed to carry weight_high of 0, therefore configuring 8-bit weights as appropriate. When dumping nexthops with 16-bit weight, it would only show the lower 8 bits. But configuring such nexthops implies existence of userspace aware of the extension in the first place. - New userspace talking to an old kernel will work as long as it only attempts to configure 8-bit weights, where the high-order bits are zero. Old kernel will bounce attempts at configuring >8-bit weights. Renaming reserved fields as they are allocated for some purpose is commonly done in Linux. Whoever touches a reserved field is doing so at their own risk. nexthop_grp::resvd1 in particular is currently used by at least strace, however they carry an own copy of UAPI headers, and the conversion should be trivial. A helper is provided for decoding the weight out of the two fields. Forcing a conversion seems preferable to bending backwards and introducing anonymous unions or whatever.

HIGH · 7.8Linux

Executive briefing

The source record describes: In the Linux kernel, the following vulnerability has been resolved: net: nexthop: Increase weight to u16 In CLOS networks, as link failures occur at various points in the network, ECMP weights of the involved nodes are adjusted to compensate. With high fan-out of the involved nodes, and overall high number of nodes, a (non-)ECMP weight ratio that we would like to configure does not fit into 8 bits. Instead of, say, 255:254, we might like to configure something like 1000:999. For these deployments, the 8-bit weight may not be enough. To that end, in this patch increase the next hop weight from u8 to u16. Increasing the width of an integral type can be tricky, because while the code still compiles, the types may not check out anymore, and numerical errors come up. To prevent this, the conversion was done in two steps. First the type was changed from u8 to a single-member structure, which invalidated all uses of the field. This allowed going through them one by one and audit for type correctness. Then the structure was replaced with a vanilla u16 again. This should ensure that no place was missed. The UAPI for configuring nexthop group members is that an attribute NHA_GROUP carries an array of struct nexthop_grp entries: struct nexthop_grp { __u32 id; /* nexthop id - must exist */ __u8 weight; /* weight of this nexthop */ __u8 resvd1; __u16 resvd2; }; The field resvd1 is currently validated and required to be zero. We can lift this requirement and carry high-order bits of the weight in the reserved field: struct nexthop_grp { __u32 id; /* nexthop id - must exist */ __u8 weight; /* weight of this nexthop */ __u8 weight_high; __u16 resvd2; }; Keeping the fields split this way was chosen in case an existing userspace makes assumptions about the width of the weight field, and to sidestep any endianness issues. The weight field is currently encoded as the weight value minus one, because weight of 0 is invalid. This same trick is impossible for the new weight_high field, because zero must mean actual zero. With this in place: - Old userspace is guaranteed to carry weight_high of 0, therefore configuring 8-bit weights as appropriate. When dumping nexthops with 16-bit weight, it would only show the lower 8 bits. But configuring such nexthops implies existence of userspace aware of the extension in the first place. - New userspace talking to an old kernel will work as long as it only attempts to configure 8-bit weights, where the high-order bits are zero. Old kernel will bounce attempts at configuring >8-bit weights. Renaming reserved fields as they are allocated for some purpose is commonly done in Linux. Whoever touches a reserved field is doing so at their own risk. nexthop_grp::resvd1 in particular is currently used by at least strace, however they carry an own copy of UAPI headers, and the conversion should be trivial. A helper is provided for decoding the weight out of the two fields. Forcing a conversion seems preferable to bending backwards and introducing anonymous unions or whatever. The practical risk depends on whether an affected product/version is present, reachable and configured in an exploitable way. Review the affected-product evidence and linked vendor advisories before assigning exposure status.

Assessment: Potential exposure only — validate the installed product, exact version, configuration and vendor applicability before treating an asset as confirmed vulnerable.

Evidence confidence: Low Evidence-derived, not an exploitability verdict

Severity & attack characteristics

7.8 / 10 · 3.1

CVSS vector:
CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:H/I:H/A:H

Attack vectorL
Attack complexityL
Privileges requiredL
User interactionN
ScopeU
Confidentiality impactH
Integrity impactH
Availability impactH

Technical explanation & impact

The technical mechanism is not expanded beyond the source description unless a referenced advisory supplies additional evidence. Read the linked vendor/CERT advisories for root-cause detail.

Potential impact must be interpreted from the published CVSS impact metrics and the affected component. A CVSS impact score is not proof that a particular asset is exploitable.

Weakness classification

CWE-787

Affected products and versions

NVD has not supplied machine-readable vulnerable CPE product/version entries for this CVE. This is an information gap, not proof that no products are affected. Check the vendor advisory references below.

Remediation & validation

  1. Identify exposure by comparing the affected product and version ranges with your asset inventory, SBOM and externally exposed services.
  2. Review the linked vendor security advisory or patch notes. Upgrade to a vendor-confirmed fixed release; do not infer a fixed version from the CVE description.
  3. Until patched, consider restricting network access or disabling the affected feature where operationally safe. These are temporary controls, not a substitute for a vendor fix.
  4. Validate the remediation with a version check and vulnerability rescan, then retain change evidence.

No fixed version is displayed unless it is explicitly established by a vendor advisory. Follow the vendor's release notes for exact product and branch applicability.

Vendor advisories, patches & exploit references

Information gaps & confidence notes

These gaps indicate missing source data. CVE Watch does not fill them with guessed product, exploit or patch details.

Last enrichment: 2026-11-04T19:02:25+00:00 · Source last modified: 2026-11-03T18:15:39.353

Open NVD record ← Back to CVE Watch